Anjney Tubes India  /  Est. 1995  /  Ahmedabad +91 93747 89875 marketing@anjney.com
Anjney Tubes India

PPCH FR compressed air piping · Pressure drop and energy

Less pressure drop. Lower power bills.

Compressed air is the most expensive utility in most plants, and the distribution line is the part nobody measures. Here is where Anjney PPCH FR saves energy, how much, and what has to be true for it to hold.

2–5%of compressor energy against a new, correctly sized line
7–13%replacing an aged, leaking, scaled metal line
0%decay over the 25+ year life of the pipe

Estimate your saving

Put in your compressor. The two scenarios use the same physics as the model below.

Your current line
Annual electricity₹22,33,800
Saving a year₹2,34,549
Saving over 10 years₹23,45,490

Indicative only. An Anjney air audit on your line replaces every estimate here with a measured figure.

Where the saving comes from

Six mechanisms. Each one can be checked on its own, so a plant engineer can accept the ones that apply to their line.

  1. A larger bore at the same ODMRS 12.5 MPa allows a thinner wall. At 110 mm OD the bore is 87 mm against 79 mm: about 21% more area and roughly 38% less friction loss at the same flow.
  2. A mirror bore that stays that wayRa 0.10 µm and Hazen-Williams C 150, against 1.0–1.7 µm and C 130 for new galvanised steel. PPCH never corrodes, so C stays at 150.
  3. No ring inside the jointButt fusion leaves a bead in every joint; threads leave a step. Socket fusion and electrofusion leave the bore clear.
  4. Fused joints do not leakOne continuous piece of polymer, with no leak path to age. Threaded joints loosen under vibration and heat cycles.
  5. A thermal break in the wallThe glass-reinforced core brings conductivity to about 0.23 W/m·K, around 300 times lower than mild steel. Less condensate forms in the main.
  6. Nothing decaysNo rust, scale or bore loss, no repainting, no joint retightening. The year-one saving is the year-twenty-five saving.

Same outside diameter. Larger bore.

Anjney published inner diameters at PN16. This advantage applies against other polymer pipes of the same OD.

ID 79PP / PPR / PPRC / PPH ID 87Anjney PPCH FR +21%bore area
End view at 110 mm OD, drawn to scale
OD (mm)PP, PPR, PPH IDPPCH FR IDBore areaFlow at equal ΔpΔp at equal flow
634550+23.5%+30.1%−41.0%
906572+22.7%+29.1%−40.0%
1107987+21.3%+27.3%−38.3%
160116127+19.9%+25.4%−36.4%

Basis: area ratio (D₂/D₁)²; flow at equal pressure drop Q ∝ D2.5; pressure drop at equal flow Δp ∝ D−5 (Darcy-Weisbach). If the old line dropped 0.6 bar, the new one drops about 0.37 bar. At about 7% of compressor power per bar, that is roughly 1.6% from this mechanism alone.

A metal line gets worse every year. PPCH does not.

Friction head loss at equal bore, relative to Anjney PPCH FR (C = 150, no decay).

Ageing galvanised or mild-steel line

Anjney PPCH FR1.00×
New GI / MS1.30×
After 2 years1.78×
After 5 years2.58×
After 8 years3.20×
After 12 years4.10×
After 15 years4.71×

Head loss scales as (C₁/C₂)1.852. Ageing C values for steel in humid compressed-air duty are engineering estimates.

Surface roughness, Ra

Anjney PPCH FR0.1 µm
Aluminium0.7 µm
Stainless steel1.1 µm
New GI / MS1.3 µm
Aged GI / MS, 5–8 years15 µm

Thermal conductivity, W/m·K (log scale)

Anjney PPCH FR0.23
HDPE0.4
Stainless steel 30416.7
Aluminium46.9
Mild steel / GI75.5

No ring inside. No leak path.

Published audits often find 20–30% of generated air lost to leaks in poorly kept systems. Not all of it is joints, but a fused system removes that part completely.

Threaded GI / MS / SSCut threads thin the wall and seal on tape. A step in the bore, and the main leak path in most air systems.
Butt fusion (HDPE, PP, PPH)A bead forms inside every joint, by design: a permanent restriction in the bore.
Anjney socket fusion, 20–160 mmThe pipe is fused inside a socket fitting. Nothing is added to the bore.
Anjney electrofusion, 160–630 mmA coil in the fitting fuses both surfaces on a machine-controlled cycle. Bore clear, every joint logged.

Watch what the bead does in air, gas and acid lines

The model, put to a number

A 30 kW compressor, 8,760 h a year, load factor 0.85, ₹10 per kWh: 2,23,380 kWh and ₹22,33,800 a year.

Scenario A New, correctly sized line

Lower distribution pressure drop0.25 bar × 7% per bar1.75%₹39,092
Joint leakage eliminated2% of generated air2.00%₹44,676
No weld bead or thread step0.30%₹6,701
Bore recovered from scaleNil, new for new0.00%₹0
Total a year4.05%₹90,469

Scenario B Aged, leaking, scaled metal line

Lower distribution pressure drop0.60 bar × 7% per bar4.20%₹93,820
Joint leakage eliminated5% of air, corroded threads5.00%₹1,11,690
Bore recovered from scale1%, tuberculation removed1.00%₹22,338
No weld bead or thread step0.30%₹6,701
Total a year10.50%₹2,34,549

Conversion used throughout: 1 bar lower compressor discharge pressure ≈ 6–7% lower specific power (US DOE / Compressed Air Challenge). Leakage converts about 1:1 into compressor energy. Over ten years that is about ₹9.0 lakh in Scenario A and ₹23.5 lakh in Scenario B.

Measure it before you order

An Anjney air audit measures the actual pressure drop, leak rate and load factor on your line, and we quote against the measured result.

Ask for an air audit

Energy saving questions

How much energy does PPCH compressed air pipe save?

Against a new, correctly sized metal or polymer line, about 2 to 5% of compressor energy. When it replaces an aged, leaking, scaled metal line, typically 7 to 13%, confirmed by an air audit on the existing line.

Why does a smoother pipe save compressor power?

Friction in the line is pressure the compressor has to make and then lose. A lower pressure drop lets you set the compressor discharge pressure lower for the same pressure at the tool. Each 1 bar lower is roughly 6 to 7% less compressor power.

Does the saving fall as the pipe ages?

No. The PPCH bore does not rust, scale or tuberculate, so the Hazen-Williams C value stays at 150. A galvanised or mild-steel line falls to about 75 to 90 within five to eight years, so the gap widens every year.

Why is the bore of PPCH larger than PPR at the same outside diameter?

The glass-reinforced composite wall has an MRS of 12.5 MPa against 8 to 10 MPa for PP, PPR, PPRC and PPH, so the wall can be thinner for the same pressure class. At 110 mm OD the bore is 87 mm against 79 mm.

Can Anjney measure the saving before we order?

Yes. Anjney carries out an air audit on the existing line and quotes against the measured pressure drop, leak rate and load factor rather than a generic percentage.

Enquiry

Send us your line schedule

Tell us the service, pipe sizes and approximate run lengths. Our technical sales team sizes the network and returns a bill of material, with an installed-cost comparison against your current specification.

Sent straight to our sales team at marketing@anjney.com. We use your details only to reply to this enquiry.

Document Open in new tab Download